More fairing on the Utility This time the transom

Warm greetings from Barnacle Mike’s crowded little boat shop. You know, one of the great things about the boatbuilding community is the fact that you meet some really cool people, both online and in person. The level of support and insight that you get from more experienced builders who kindly share their knowledge and give advice can truly help a newbie keep pushing his or her project forward. I’m very thankful for that.

An online boatbuilding friend, who has also been kind enough to follow my blog, sent me an e-mail the other day asking about the status of the Utility. It does seem like I’ve been paying a bit much attention to the Zip project lately. Truth is, I have still been slowly, slowly... s-l-o-w-l-y... fairing away at the Utility all the while. Still, his inquiry about its status gave me a little more motivation to get off my “transom” and put more elbow grease into getting the little boat past the fairing stage. (Thank you, Paul!)

So, that’s just what I did Saturday, fairing away at the transom sides until they were finished. The starboard side had a bit more excess material than the port side. So, I roughed it in with the belt sander, then worked it the rest of the way down with the mouse sander. Unfortunately, I did not follow the “best practice” of checking my work frequently with my test piece of plywood. (I thought the transom sides would be a no-brainer. I was wrong.) When I tested my “finished” work with the plywood, expecting to feel a broad smile cross my face as I witnessed my handiwork, I was disappointed to see several gaps appear. The culprit was an overly sharp bevel in a couple of spots. More gaps to fill with thickened epoxy. I’m getting pretty good at that, if I do say so myself.

Needless to say,  I was more cautious with the port side. I also went about it a little differently. This time, I started by carrying the line of the sheer and chine through the transom material first. Then, I “connected” the two spots by fairing the area in-between. This time I alternated between the mouse sander and a small block plane. I worked slowly and purposefully.

The results were much, much better.

I do still have a good bit more fairing to do, primarily in the mid-section of the boat. I also have to make a decision about the chines in that area, (more on that later). I could’ve worked on all this Sunday. However, yours truly decided he needed some time on the water. So, I spent the day canoeing. I’m sure you understand.

By the way, I met another boatbuilder out on the river. He was piloting a very nice-looking red drift boat upriver. It looked about 16’ long. The handsome-looking boat glided smoothly through the water, pushed by a silent electric trolling motor. He proudly said “yes” when I asked if he’d built it himself. He had some very nice things to say about Don Hill’s drift boat plans before we each went our separate ways. 

Yep. You’ve gotta love the boatbuilding community.

Starboard transom-chine joint after fairing.

Starboard transom-chine joint after fairing.

Starboard transom-chine joint after fairing

Starboard transom-sheer joint after fairing. As you can see, Ive got a heck of a gap in that "Marine-Grade" plywood that Im going to have to fill.

Port transom-chine joint before fairing.

Port transom-chine joint before fairing.

Port transom-chine joint after fairing.

Port transom-sheer joint before fairing. Notice all that epoxy thickened with #2 silica?

Port transom-sheer joint after fairing. I still have some thickened epoxy to file away.

Read More..

Just In Time Upcycling

In the old days, like back as far as the 60s people used to re-use stuff.  Then along came re-cycling which was not the same as re-use.  Re-cycling meant grinding stuff up and then using it as feed stock for something brand-new.  Old stuff was passe. New stuff was hip.  Recycling was something that hippies did.  Re-use was something your mom or your grandmother did. That is, your mom didnt throw away your old clothes but patched them up or made them last a while longer by maybe altering them or embroidering on them or turning old stuff into quilts, or your dad would take bent nails and pound on them with a hammer till they were straight again and could have another life. 
And then, stuff became so cheap that re-use became too quaint for any reasonable person to countenance.  Re-use became more expensive if you counted your time than simply throwing stuff away and buying new.  That was in the days when people had jobs.
But now that jobs are going extinct, more and more people dont have jobs and all of a sudden, re-use isnt such a stupid proposition.  But re-use isnt a cool name for what we are doing and instead it has been re-branded as up-cycling. Whatever. 
It is what it is and little by little, more and more people are tapping into the recycling and waste stream and extracting materials from it that once upon a time were practically worthless.  Instead of grinding everything down to pulp and then squirting it out of some machine to make new stuff, more and more people are taking the practically worthless stuff and using it as is or modifying it just a little to fit their own use.  Nothing new, really, but as more and more people do this, the stuff that used to be worthless will become more and more precious.  With nobody having jobs and the money to buy the new stuff made from old stuff, the old stuff as is without being recycled will become more expensive.
So this is where the concept of just-in-time upcycling comes in.  You have to grab stuff out of the waste stream and modify it to suit you while you can, before everyone else realizes that this is where its at and makes the stuff that is now being thrown away into an expensive commodity.
Check out Wendy Tremayne and The Good Life in my next post for more on this topic.

Read More..